Green Laser System

DPSS Green Laser System

Diode / DPSS Laser	Mounting Option

DPSS Laser System	Fiber Coupling System

CW, Q-switched, AOM Q-switched

532nM / Single Longitudinal Mode

Low Noise (< 1% - 0 to 20MHz)

TEMoo ~95%

Internal Temprature Stablizer

Stable Output Power

On/Off Key Lock Switch

Function Panel Display

Optional Fiber Coupling

CDRH Complied
Heat Sink Fan

Single Longitudinal, Low Noise ( < 1% , 0 to 20MHz) CW Laser System
Item No. Po (mW) Max. Beam Diameter (mm) Beam Divergence (mrad, full angle) Long Term Stability
GSLN32-50 50 1.5 0.8 < 2% / 8hrs
GSLN32-20 20 1.5 0.8 < 2% / 8hrs
FGSLN32-50-SMPM-FC 50 1.5 0.8 < 2% / 8hrs

AOM (High Speed Q-switched via Acousto-Optic Modulator) Laser System

Item No.	l (nm)	Pulse Energy at 1KHz	Pulse Duration at 1KHz	Max. Pulse Repetition Rate	Average Output Power
GSQAOM32-25	532	25 µJ	< 10 nsec	10 KHz	> 35mW
GSQAOM32-20	532	20 µJ	< 10 nsec	10 KHz	> 25mW
GSQAOM32-10	532	10 µJ	< 10 nsec	10 KHz	> 15mW

CW Laser System

Item No.	Po (mW) Max.	Beam Diameter (mm)	Beam Divergence (mrad)	Stability
GS32-5	5	1.0	1.2	15%
GS32-10	10	1.0	1.2	15%
GS32-20	20	1.0	1.2	15%
GSF32-5P	5	1.0	1.2	2%
GSF32-10P	10	1.0	1.2	2%
GSF32-20P	20	1.0	1.2	2%
GSF32-50PS	50	1.5	0.8	5%
GSF32-100PS	100	1.0	1.2	5%
GSF32-150PS	150	1.0	1.2	10%
GSF32-200PS	200	1.5	1.2	10%
GSF32-200P	200	1.5	0.8	2%
GSF32-300PS	300	1.5	1.2	10%
GSF32-1000PS	1000	1.5	1.2	10%

Item No.: GSLN32-50
CW Laser

CW, Single Longitudinal Mode
Wavelength: 532 nM
Output Power: 50 mW
Transverse Mode: TEMoo, M² < 1.2 (typ.1.05)
Noise (10Hz - 20 MHz): < 0.5 RMS (typ. 0.1% RMS)
Line Width: < 0.00001 nm
Beam Divergence (Full angle 1/e²): 0.6 mrad
Beam Diameter at outpout: 1.1 mm
Coherence Length: > 50 M
Ellipticity: 0.95 -1.05
Beam Pointing Stability: < 0.05 mrad
Laser head size: 50 x 90 x 190 mm
Power Stability: < 2%
Heating Power: < 15 W (typ. 8 W)
Housing base temperature range: 15 - 45 °C
Polarization: linear > 100:1, Horizontal (Optional vertical)
Function panel display
Optional Heat Sink / Fan
Adjustable output power via digital controller with 1 mW resolution
Internal over heat automatic shut off
Microprocessor controlled laser driver/power supply
(90 x 260 x 197mm)
Cable length: 52 inches (132cm)
Operating Voltage: 115±20% VAC - 230±15% VAC / 50 - 60Hz (selectable)

Item No.: GSLN32-20
CW Laser

CW, Single Longitudinal Mode
Wavelength: 532 nM
Output Power: 20 mW
Transverse Mode: TEMoo, M² < 1.2 (typ.1.05)
Noise (10Hz - 20 MHz): < 0.5 RMS (typ. 0.1% RMS)
Line Width: < 0.00001 nm
Beam Divergence (Full angle 1/e²): 0.6 mrad
Beam Diameter at outpout: 1.1 mm
Coherence Length: > 50 M
Ellipticity: 0.95 -1.05
Beam Pointing Stability: < 0.05 mrad
Laser head size: 50 x 90 x 190 mm
Power Stability: < 2%
Heating Power: < 15 W (typ. 8 W)
Housing base temperature range: 15 - 45 °C
Polarization: linear > 100:1, Horizontal (Optional vertical)
Function panel display
Optional Heat Sink / Fan
Adjustable output power via digital controller with 1 mW resolution
Internal over heat automatic shut off
Microprocessor controlled laser driver/power supply
(90 x 260 x 197mm)
Cable length: 52 inches (132cm)
Operating Voltage: 115±20% VAC - 230±15% VAC / 50 - 60Hz (selectable)
Optional Heat Sink / Fan

Item No.: GSQAOM32-25

AOM - High Speed Q-Switched via Acousto-Optic Modulator Laser

Q-Switched with AOM, ext./int. triggering
Wavelength: 532 nM
Pulse energy at 1 KHz: > 25 µJ
Pulse energy at 10 KHz: > 3 µJ
Average Pout (at 3 KHz): > 35 mW
Output power stability: 10% RMS (typ.)
M²: Better than 1.5
Pulse repetition rate:
- external triggering: 0 -10 KHz
- internal triggering: 0.01 - 10 KHz
Pulse Duration at 1 KHz: < 10 ns
Beam Divergence (Half angle 1/e²): 1.5 mrad
Beam Diameter: 0.4 mm
Polarization: linear > 100:1, Horizontal (Optional vertical)
Laser head size: 52 x 90 x 260mm
Function panel display
Internal over heat automatic shut off
Microprocessor controlled laser driver/power supply
(95 x 252 x 252mm)
Cable length: 52 inches (132cm)
Operating Voltage: 115±20% VAC - 230±15% VAC / 50 - 60Hz (selectable)
Optional DC Driven Laser Driver/Controller
Size: 66 x 90 x 185 mm
Input Voltage: 24 VDC,< 100W

Item No.: GSQAOM32-20

AOM - High Speed Q-Switched via Acousto-Optic Modulator Laser

Q-Switched with AOM, ext./int. triggering
Wavelength: 532 nM
Pulse energy at 1 KHz: > 20 µJ
Pulse energy at 10 KHz: > 3 µJ
Max. Average Pout (at 3 KHz): > 25 mW
Output power stability: 10% RMS (typ.)
M²: Better than 1.5
Pulse repetition rate:
- external triggering: 0 -10 KHz
- internal triggering: 0.01 - 10 KHz
Pulse Duration at 1 KHz: < 10 ns
Pulse Duration at 10 KHz: < 15 ns
Beam Divergence (Half angle 1/e²): 1.5 mrad
Beam Diameter: 0.4 mm
Polarization: linear > 100:1, Horizontal (Optional vertical)
Laser head size: 52 x 90 x 260mm
Function panel display
Internal over heat automatic shut off
Microprocessor controlled laser driver/power supply
(95 x 252 x 252mm)
Cable length: 52 inches (132cm)
Laser Head Heating Power, W: < 50
Operating Voltage: 115±20% VAC - 230±15% VAC / 50 - 60Hz (selectable)
Optional DC Driven Laser Driver/Controller
Size: 66 x 90 x 185 mm
Input Voltage: 24 VDC,< 100W

Item No.: GSQAOM32-10

AOM - High Speed Q-Switched via Acousto-Optic Modulator Laser

Q-Switched with AOM, ext./int. triggering
Wavelength: 532 nM
Pulse energy at 1 KHz: > 10 µJ
Pulse energy at 10 KHz: > 1 µJ
Max. Average Pout (at 3 KHz): > 15 mW
Output power stability: 10% RMS (typ.)
M²: Better than 1.5
Pulse repetition rate: 10 KHz
- external triggering: 0 -10 KHz
- internal triggering: 0.01 - 10 KHz
Pulse Duration at 1 KHz: < 10 ns
Beam Divergence (Half angle 1/e²): 1.5 mrad
Beam Diameter: 0.4 mm
Polarization: linear > 100:1, Horizontal (Optional vertical)
Laser head size: 52 x 90 x 260mm
Function panel display
Internal over heat automatic shut off
Microprocessor controlled laser driver/power supply
(95 x 252 x 252mm)
Cable length: 52 inches (132cm)
Operating Voltage: 115±20% VAC - 230±15% VAC / 50 - 60Hz (selectable)
Optional DC Driven Laser Driver/Controller
Size: 66 x 90 x 185 mm
Input Voltage: 24 VDC,< 100W

Item No.: GS32-5
CW Laser

CW
Wavelength: 532 nM
Output Power: 5 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Laser head size: 45 x 60 x 120mm
Power Stability: < 15%
Output power adjustable
Modulation Control (up to 5K)
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 750mA
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GS32-10
CW Laser

CW
Wavelength: 532 nM
Output Power: 10 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Laser head size: 45 x 60 x 120mm
Power Stability: < 15%
Output power adjustable
Modulation Control (up to 5K)
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 750mA
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GS32-20
CW Laser

CW
Wavelength: 532 nM
Output Power: 20 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Laser head size: 45 x 60 x 120mm
Power Stability: < 15%
Output power adjustable
Modulation Control (up to 5K)
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 750mA
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GSF32-5P
CW Laser

CW
Wavelength: 532 nM
Output Power: 5 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Line Width: < 0.2 nm
Laser head size: 45 x 60 x 120mm
Power Stability: < 2%
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 750mA
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GSF32-10P
CW Laser

CW
Wavelength: 532 nM
Output Power: 10 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Line Width: < 0.2 nm
Laser head size: 45 x 60 x 120mm
Power Stability: < 2%
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 750mA
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GSF32-20P
CW Laser

CW
Wavelength: 532 nM
Output Power: 20 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Line Width: < 0.2 nm
Laser head size: 45 x 60 x 120mm
Power Stability: < 2%
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 750mA
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GS32-50
CW Laser

CW
Wavelength: 532 nM
Output Power: 50 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Laser head size: 45 x 95 x 130 mm
Power Stability: < 5%
Modulation Control (up to 5K)
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 1.4 A
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GS32-100
CW Laser

CW
Wavelength: 532 nM
Output Power: 100 mW
Beam Divergence (Half angle 1/e²): 0.6mrad
Beam Diameter: 1.0mm
Laser head size: 45 x 95 x 130 mm
Power Stability: < 15%
Output power adjustable
Modulation Control (up to 5K)
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 1.4 A
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A

Item No.: GS32-150
CW Laser

CW
Wavelength: 532 nM
Output Power: 150 mW
Beam Divergence (Half angle 1/e²): 0.6 mrad
Beam Diameter: 1.0 mm
Laser head size: 45 x 95 x 130 mm
Power Stability: < 15%
Output power adjustable
Modulation Control (up to 5K)
Key lock switch
LED emission indicator on/off switch
Operating Voltage: 5VDC / Max. 1.4 A
Mounting Option
Power Supply: 26 x 41 x 55 mm
- Input: 100 - 240 VAC, 50 - 60Hz
- Ouput: 5VDC, Max. 1,6A